华为命令手册

华为交换机命令手册

PCA login: root ；使用root用户

password: linux ；口令是linux

# shutdown -h now ；关机

# init 0 ；关机

# logout

# login

# ifconfig ；显示IP地址

# ifconfig eth0 netmask ；设置IP地址

# ifconfig eht0 netmask down ; 删除IP地址

# route add 0.0.0.0 gw

# route del 0.0.0.0 gw

# route add default gw ；设置网关

# route del default gw ；删除网关

# route ；显示网关

# ping

# telnet ；建议telnet之前先ping一下

－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－

交换机命令

~~~~~~~~~~

[Quidway]super password 修改特权用户密码

[Quidway]sysname 交换机命名

[Quidway]interface ethernet 0/1 进入接口视图

[Quidway]interface vlan x 进入接口视图

[Quidway-Vlan-interfacex]ip address 10.65.1.1 255.255.0.0

[Quidway]ip route-static 0.0.0.0 0.0.0.0 10.65.1.2 静态路由＝网关

[Quidway]user-interface vty 0 4

[S3026-ui-vty0-4]authentication-mode password

[S3026-ui-vty0-4]set authentication-mode password simple 222

[S3026-ui-vty0-4]user privilege level 3

[Quidway-Ethernet0/1]duplex {half|full|auto} 配置端口双工工作状态

[Quidway-Ethernet0/1]speed {10|100|auto} 配置端口工作速率

[Quidway-Ethernet0/1]flow-control 配置端口流控

[Quidway-Ethernet0/1]mdi {across|auto|normal} 配置端口MDI/MDIX状态平接或扭接

[Quidway-Ethernet0/1]port link-type {trunk|access|hybrid} 设置接口工作模式

[Quidway-Ethernet0/1]shutdown 关闭/重起接口

[Quidway-Ethernet0/2]quit 退出系统视图

[Quidway]vlan 3 创建/删除一个VLAN/进入VLAN模式

[Quidway-vlan3]port ethernet 0/1 to ethernet 0/4 在当前VLAN增加/删除以太

网接口

[Quidway-Ethernet0/2]port access vlan 3 将当前接口加入到指定VLAN

[Quidway-Ethernet0/2]port trunk permit vlan {ID|All} 设trunk允许的VLAN

[Quidway-Ethernet0/2]port trunk pvid vlan 3 设置trunk端口的PVID

[Quidway]monitor-port 指定和清除镜像端口

[Quidway]port mirror 指定和清除被镜像端口

[Quidway]port mirror int_list observing-port int_type int_num 指定镜像和被镜像

[Quidway]description string 指定VLAN描述字符

[Quidway]description 删除VLAN描述字符

[Quidway]display vlan [vlan_id] 查看VLAN设置

[Quidway]stp {enable|disable} 开启/关闭生成树,默认关闭

[Quidway]stp priority 4096 设置交换机的优先级

[Quidway]stp root {primary|secondary} 设置交换机为根或根的备份

[Quidway-Ethernet0/1]stp cost 200 设置交换机端口的花费

[SwitchA-vlanx]isolate-user-vlan enable 设置主vlan

[SwitchA]Isolate-user-vlan secondary 设置主vlan包括的子vlan

[Quidway-Ethernet0/2]port hybrid pvid vlan 设置vlan的pvid

[Quidway-Ethernet0/2]port hybrid pvid 删除vlan的pvid

[Quidway-Ethernet0/2]port hybrid vlan vlan_id_list untagged 设置无标识的vlan

如果包的vlan id与PVId一致，则去掉vlan信息. 默认PVID=1。

所以设置PVID为所属vlan id, 设置可以互通的vlan为untagged.

－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－

路由器命令

~~~~~~~~~~

[Quidway]display version 显示版本信息

[Quidway]display current-configuration 显示当前配置

[Quidway]display interfaces 显示接口信息

[Quidway]display ip route 显示路由信息

[Quidway]sysname aabbcc 更改主机名

[Quidway]super passwrod 123456 设置口令

[Quidway]interface serial0 进入接口

[Quidway-serial0]ip address

[Quidway-serial0]undo shutdown 激活端口

[Quidway]link-protocol hdlc 绑定hdlc协议

[Quidway]user-interface vty 0 4

[Quidway-ui-vty0-4]authentication-mode password

[Quidway-ui-vty0-4]set authentication-mode password simple 222

[Quidway-ui-vty0-4]user privilege level 3

[Quidway-ui-vty0-4]quit

[Quidway]debugging hdlc all serial0 显示所有信息

[Quidway]debugging hdlc event serial0 调试事件信息

[Quidway]debugging hdlc packet serial0 显示包的信息

静态路由：

[Quidway]ip route-static {interface

number|nexthop}[value][reject|blackhole]

例如：

[Quidway]ip route-static 129.1.0.0 16 10.0.0.2

[Quidway]ip route-static 129.1.0.0 255.255.0.0 10.0.0.2

[Quidway]ip route-static 129.1.0.0 16 Serial 2

[Quidway]ip route-static 0.0.0.0 0.0.0.0 10.0.0.2

动态路由：

[Quidway]rip

[Quidway]rip work

[Quidway]rip input

[Quidway]rip output

[Quidway-rip]network 1.0.0.0 ;可以all

[Quidway-rip]network 2.0.0.0

[Quidway-rip]peer ip-address

[Quidway-rip]summary

[Quidway]rip version 1

[Quidway]rip version 2 multicast

[Quidway-Ethernet0]rip split-horizon ;水平分隔

[Quidway]router id A.B.C.D 配置路由器的ID

[Quidway]ospf enable 启动OSPF协议

[Quidway-ospf]import-route direct 引入直联路由

[Quidway-Serial0]ospf enable area 配置OSPF区域

标准访问列表命令格式如下：

acl [match-order config|auto] 默认前者顺序匹配。

rule [normal|special]{permit|deny} [source source-addr source-wildcard|any]

例：

[Quidway]acl 10

[Quidway-acl-10]rule normal permit source 10.0.0.0 0.0.0.255

[Quidway-acl-10]rule normal deny source any

扩展访问控制列表配置命令

配置TCP/UDP协议的扩展访问列表：

rule {normal|special}{permit|deny}{tcp|udp}source {|any}destination |any}

[operate]

配置ICMP协议的扩展访问列表：

rule {normal|special}{permit|deny}icmp source {|any]destination {|any]

[icmp-code] [logging]

扩展访问控制列表操作符的含义

equal portnumber 等于

greater-than portnumber 大于

less-than portnumber 小于

not-equal portnumber 不等

range portnumber1 portnumber2 区间

扩展访问控制列表举例

[Quidway]acl 101

[Quidway-acl-101]rule deny souce any destination any

[Quidway-acl-101]rule permit icmp source any destination any icmp-type echo

[Quidway-acl-101]rule permit icmp source any destination any icmp-type echo-reply

[Quidway]acl 102

[Quidway-acl-102]rule permit ip source 10.0.0.1 0.0.0.0 destination 202.0.0.1 0.0.0.0

[Quidway-acl-102]rule deny ip source any destination any

[Quidway]acl 103

[Quidway-acl-103]rule permit tcp source any destination 10.0.0.1 0.0.0.0 destination-port equal ftp

[Quidway-acl-103]rule permit tcp source any destination 10.0.0.2 0.0.0.0 destination-port equal www

[Quidway]firewall enable

[Quidway]firewall default permit|deny

[Quidway]int e0

[Quidway-Ethernet0]firewall packet-filter 101 inbound|outbound

地址转换配置举例

[Quidway]firewall enable

[Quidway]firewall default permit

[Quidway]acl 101

[Quidway-acl-101]rule deny ip source any destination any

[Quidway-acl-101]rule permit ip source 129.38.1.4 0 destination any

[Quidway-acl-101]rule permit ip source 129.38.1.1 0 destination any

[Quidway-acl-101]rule permit ip source 129.38.1.2 0 destination any

[Quidway-acl-101]rule permit ip source 129.38.1.3 0 destination any

[Quidway]acl 102

[Quidway-acl-102]rule permit tcp source 202.39.2.3 0 destination 202.38.160.1 0

[Quidway-acl-102]rule permit tcp source any destination 202.38.160.1 0 destination-port great-than

1024

[Quidway-Ethernet0]firewall packet-filter 101 inbound

[Quidway-Serial0]firewall packet-filter 102 inbound

[Quidway]nat address-group 202.38.160.101 202.38.160.103 pool1

[Quidway]acl 1

[Quidway-acl-1]rule permit source 10.110.10.0 0.0.0.255

[Quidway-acl-1]rule deny source any

[Quidway-acl-1]int serial 0

[Quidway-Serial0]nat outbound 1 address-group pool1

[Quidway-Serial0]nat server global 202.38.160.101 inside 10.110.10.1 ftp tcp

[Quidway-Serial0]nat server global 202.38.160.102 inside 10.110.10.2 www tcp

[Quidway-Serial0]nat server global 202.38.160.102 8080 inside 10.110.10.3 www tcp

[Quidway-Serial0]nat server global 202.38.160.103 inside 10.110.10.4 smtp

udp

PPP验证：

主验方：pap|chap

[Quidway]local-user u2 password {simple|cipher} aaa

[Quidway]interface serial 0

[Quidway-serial0]ppp authentication-mode {pap|chap}

[Quidway-serial0]ppp chap user u1 //pap时，不用此句

pap被验方：

[Quidway]interface serial 0

[Quidway-serial0]ppp pap local-user u2 password {simple|cipher} aaa

chap被验方：

[Quidway]interface serial 0

[Quidway-serial0]ppp chap user u1

[Quidway-serial0]local-user u2 password {simple|cipher} aaa